Receiver GR-16 HoTT - Version 6a39

GR-16 HoTT | #33508
 Gr-16_eng Version: V 6a39 
Other downloads: - Handbuch, Manual, Manuel
- Firmware-Upgrade
Changes:

V6a37
- SUMO: Failsafe/Hold settable. SUMO AUS by Failsafe: when an output is set on OFF.

V6a38
- 0 values are prevented for telemetry outputs
- Telemtry is faster
- The version with FS in the name outputs of the original SUMD protocol with FAILSAFE BIT
- The version without FS in the name outputs the SMUD protocol without FAILSAFE BIT (for flybarless systems that have not implemented the SUMD protocol correctly)

V6a39 from 27 June 2017
- Voltage measurement adjustable on channel 6.

Attention: Voltage divider on channel 6 necessary as similar with the receiver #33576 or use the controller S3082 or S3083. The voltage divider is built in the controller S3082 and S3083.

Changes from 02. August 2017
- New manual GR-16 available

Specials:

The update should be performed with the Firmwareupgrader >3.7.
The update must be performed 2 times
Thereafter a factory reset should be performed

Attention: After the update a factory reset should be performed!
Push and hold the Bind button then switch the receiver ON and wait about 3 seconds until the LED light up.
Release the button. Without reset the servos might run to their mechanical end point!
Tags: GR-16
Please enter these characters in the following text field.

The fields marked with * are required.

  • Product code error

    Hello, I need advice.When I upgrading the receiver with grStudio ( 4.7 ) I get an error message : Product code error. Product codes that are different from the inside firmware file.

    Device Product Code : 16003324
    Firmware Product Code : 16003100

    Download Process Stop

    Firmware is downloaded from this site.

    Thanks for help.

  • Answer to "Product code error"

    Hello Peter,

    thank you very much for your comment.
    Your error message is unknown to us. Please send your receiver back to our service department.
    Further details you will find under Graupner Service https://www.graupner.com/Graupner-Service

    We will check the receiver as soon as possible

    Thank you

    Kind regards

    Graupner

  • older firmware

    Hello, can you send me an older firmware version? Or where would I find it? I can test it.

  • Answer to "older firmware"

    Hello Peter,

    we are displaying only the current firmware update.
    Please let us know which older firmware update you want and I will look after it.

    Kind regards

    Graupner

  • older firmware

    Hi, i have problem with RC signal lost.

    Requesting status information from Flight-Ctrl ( Mikrokopter )
    Version 2.18b ,
    Errorcodes: 0x00 0x08
    - no receiver signal

    I want to update the receiver firmware, but I can not tell the current version.I do not know where this can be found.I need firmware version compatible with Flight-Ctrl ( Mikrokopter ) Version 2.18b.

    Firmware Version V 6a38 Is not compatible with my GR-16 HoTT 33508.

    So if you can send me the older firmware for the test. Thank you.





  • Answer "older firmware"

    Hello Peter,

    the firmware version V6a38 should be compatible.
    Beside your receiver is very old or your GR-16L is from the USA. Then please let us know the serial number.
    Please get in touch with our service. service@graupner.de
    Or you can send your receiver to our service department.

    Kind regards

    Graupner

  • dont understand the 2 versions FS no FS and the details 2

    Hello (again with another Drone and reciver)

    i have a Graupner MZ-24 Pro with firmware 2.21 and this GR-16 No 33508 and your voltage module XH 33631 (who is dosent work actualy...).

    i am connected in SUMO (like ppm 1 wire) use this with a quad drone for Filming the TBS Discovery Pro with NAZA M-2 GPS, with lipo 4S 5200mah 10a

    Questions:

    i saw is 2 differents versions inside this zip file.

    1- what is this version ""33508_FS_gr_rx8_6a39_f9.bin"" ? what is the difference compare to the other one ? and what mean this "FS" ?

    2- what mean this details firmware you writen here : This can fix my problem of Voltage module XH 33631 ??

    **********************
    - Voltage measurement adjustable on channel 6.

    Attention: Voltage divider on channel 6 necessary as similar with the receiver #33576 or use the controller S3082 or S3083.
    The voltage divider is built in the controller S3082 and S3083.
    ***************************

    I realy dont understanf for what is this please explain in easy way :) and what i have to care regarding with what i am flying.

    and if you can help me to fix my voltage module it will be welcome because i just dont saw the line option on the graupnet (was working fine with GR-18 with gyro)

  • Answer "dont understand the 2 versions FS no FS and the details 2"

    Hello DRMICRO,

    thank you for your comment.

    What problem do you have with the 33631? If you set CH9 to sensor, it should work.

    If you use a voltage divider and connect it to CH9 and select voltage, you can messure the voltage directly. But be careful, without voltage devider, you may destroy the receiver. Please download the 33576 manual to check which kind of voltage divider is needed.

    We hope that we could answer your question. Otherwise plese get in touch with our service department dirctly.

    Kind regards

    Graupner

  • Minimum input voltage on channel 6

    Hi,
    After updating GR-16 (#33508) to 3a39, I have a problem with the alarm "minimum input voltage" on channel 6, all the time squeaking ...
    How to turn it off?
    Transmitter (MX-16 Hott) I have integrated with brain2 + telemetry and to port 6 I have nothing connected. In "setting and data view" channel 6 is set to servo.
    If there is no solution, send me 3a38 software at 8radzio@wp.pl

  • Answer "Minimum input voltage on channel 6"

    Hello Radoslaw,

    I think you forgot to make the factory reset after the update.

    Otherwise, please adjust 6CH Funktion: Servo, if you don't use the voltage messurement.

    Kind regards

    Graupner

  • dont understand the 2 versions FS no FS and the details

    Sir Graupner

    can you please answer to my 2 questions first about i posted ???? please forget the problem i have with the Voltage module XH 33631.

    PLEASE answer to all my questions it was long for me to write all and give you in details my configuration.

    PLEASE ANSWER TO MY QUESTIONS of the On: 29 July 2017

    i am waiting since long to have one.

    Wish you the best

  • Answer "dont understand the 2 versions FS no FS and the details 2"

    Hello DRMICRO,

    thank you for your comment.
    Our CTO will answer you directly.

    Kind regards

    Graupner

Related products
GR-16 receiver HoTT GR-16 receiver HoTT

Shipping 1-3 workdays

€76.99 *