Brushless Control T 60 - T 160

Brushless Control 60-160 +T HV, SBEC, Opto | #S3031-S3042
esc_1_eng esc_2:eng
esc_3_eng
Version:

HV_OPTO_1a484   
HV_SBEC_1a484 

new Version
AIR_ESC_HV_12S_2.010b         (ESC telemetry)
AIR_ESC_OPTO_12S_2a010b   (ESC telemetry)

AIR3G_12_2a010_EAM               (EAM telemtery)
AIR3G_12OPTO_2a010_EAM     (EAM telemetry)

Changes:


V 1a484
- The governor function is displayed

V 2.000 AIR_ESC_Heli & V1a490_Airplane
- Upgraded the Governor Mode for Helicopter
- The use of ESC telemetry is possible simultaneously with an Electric Air module

V 2001beta
- With the update 2.001, several sensors now work simultaneously.
- The governor must be trained with blades, full battery and a regulator opening of> 60%.

2a005 from 12 March 2018
- Improved governor
- With throttle -90 ...- 40% a bailout (fast start after autorotation) up to 120 seconds autorotoation is possible
- <-92% throttle is the bailout time as previously only 4 seconds
- No diode required when connecting a buffer battery
- With the same controller mouth after the speed has been taught-in, the speed of the 2.00x versions is up to 25% higher than the 1.484 and must therefore be flown again.

Version 2a005.eam from 13 April 2018
- For two engine models so that the data from both engines can be captured
- No diode required when connecting a buffer battery
- With the same controller mouth after the speed has been taught-in, the speed of the 2.00x versions is up to 25% higher than the 1.484 and must therefore be flown again.

Version 2a005eam for OPTO Controller for 18 April 2018
- For two engine models so that the data from both engines can be captured
- No diode required when connecting a buffer battery
-
With the same controller mouth after the speed has been taught-in, the speed of the 2.00x versions is up to 25% higher than the 1.484 and must therefore be flown again.

V2a010b for OPTO and HV ESCs from 10th Oct. 2018
- improved governor after low load situations in the Heli

Attention:

Update over PRO connection. Power supply over the transmitter battery connection.

Please note: With the same controller mouth after the speed has been taught-in, the speed of the 2.00x versions is up to 25% higher than the 1.484 and must therefore be flown again.

A beta version of a program is an unfinished version that has already passed the alpha stage. Although the program can be used in its basic functions, it has not yet been fully tested for errors. This means that using the beta may cause crashes or bugs.

Please enter these characters in the following text field.

The fields marked with * are required.

  • No diode required when connecting a buffer battery

    Is there any extra information available about the "No diode required when connecting a buffer battery" change.
    In the manual there is a clear statement -> "If you want to connect a battery to the BEC system, a diode (e.g.
    Schottky diode 91505) needs to be soldered into the BECs red wire, so that the current can only fl ow from the BEC to the receiver."

    "This will prevent a backflow into the controller, which could destroy the controller"

    Any additional information would be nice..

  • Answer "No diode required when connecting a buffer battery"

    Hello Kraus,

    only with Software 2.005 this diode is not needed any more. The backward current is prevented by software now.

    Kind regards

    Graupner

Related products
Brushless Control +T60, Opto, D3,5 Brushless Control +T60, Opto, D3,5

Shipping 1-3 workdays

€186.99 * €117.00 *
contr. BRUSHLESS CONTROL + T 120 Opto G6 contr. BRUSHLESS CONTROL + T 120 Opto G6

Shipping 1-3 workdays

€249.99 *
contr. BRUSHLESS CONTROL + T 160 Opto G6 contr. BRUSHLESS CONTROL + T 160 Opto G6

Shipping 1-3 workdays

€326.99 *
contr. BRUSHLESS CONTROL + T 100 Opto G6 contr. BRUSHLESS CONTROL + T 100 Opto G6

Shipping 1-3 workdays

€235.99 *
contr. BRUSHLESS CONTROL + T 120 HV G6 contr. BRUSHLESS CONTROL + T 120 HV G6

Shipping 1-3 workdays

€276.99 *
Brushless Control +T80 HV, D3,5 Brushless Control +T80 HV, D3,5

Shipping 1-3 workdays

€199.99 *
contr. BRUSHLESS CONTROL +T 80 Opto D3,5 contr. BRUSHLESS CONTROL +T 80 Opto D3,5

Shipping 1-3 workdays

€169.99 *
contr. BRUSHLESS CONTROL + T 160 HV COOL contr. BRUSHLESS CONTROL + T 160 HV COOL

Shipping 1-3 workdays

€368.99 *